Delivery times are only valid if deliveries are made on time by the relevant manufacturer!
The service tool for the technician on site.
with locator 09990000022 for Han D und Han ELocator 09990000343 for Han-Yellock has to be ordered separate!
use for following crimp contacts:
Locator for Hand-Crimping-Tool 09990000021
use for:Han-Yellock
for replacementLocator for Hand-Crimping-Tool 09990000021
use for:Han DHan E
Harting crimping tool for Han C, Han D, Han Ewith locatorwire gauge 1,5 - 4 mm˛ for Han Cwire gauge 0,14 - 1,5 mm˛ for Han Dwire gauge 0,5 - 4 mm˛ for Han Ewire gauge 0,5 - 4 mm˛ for Han-Yellock
Robust standard handtool with very good performance.scope of delivery:incl. locator for Han D, Han E, Han CLocator 09990000341 for Han-Yellock has to be ordered separate!
Locator for Hand-Crimping-Tool 09990000110
for replacementLocator for Hand-Crimping-Tool 09990000110
use for:Han D,Han E,Han C
use for male and female Crimp contacts AWG 26 - 12:
scope of delivery:Positioner and directions for use
Positioner for Four-Indent Hand-Crimping-Tool 09990000888spare part
use for:Han D,Han E,Han-Yellock,Han C
Go / no-go gauge for handtool 09990000888
crimping tool for Han C contacts with high wire gaugeswire gauge 4,0mm˛, AWG12, 6,0mm˛, AWG10 and 10,0mm˛, AWG8with positioner
Daniels (DMC) handcrimping tool for turned male and female contacts4 ident crimp in acc . to MIL 22 520/2-01wire gauge 0,09 up to 0,82mm˛, AWG32 - 20without locator - locator has to be ordered separately!
locator for Daniels (DMC) hand crimping tool 09 99 000 0501for D-Sub contacts AWG18-28, 0,82-0,09mm˛
HARTING hand crimping tool for LWL-connectorsSC, F-SMA F-ST,SW 3,8 mm, SW 4,3 mm, SW 4,95 mm,for crimping the strain relief to the connector F.O. cable for glass fiber
HARTING hand crimping tool for LWL-connectors (plastic-fibre)SW 6,95 mm, SW 4,95 mm, SW 3 mmfor crimping the strain relief to the connector F.O. cable for plastic fibre
HARTING four-ident hand crimping toolfor following 1 mm POF LWL-connectors:Han D ® , Han E ® , DIN 41 626, Ferrule, F-SMA, -ST
for turned contacts 0.14-1.0; 1.5, 2.5 and 4.0mm˛
can be used u. a. for:
for assembling of Harting RJ Industrial Gigalink Cat. 6A connectorsstraight action principleratchet releasecross section range AWG28/7 - 24/7; 0,10 - 0,25mm²
Harting crimping tool for coaxial contacts
Harting crimping tool for stamped D-Sub contacts 0,09 - 0,56 mm˛2 Crimp nests AWG 28-24 and AWG 26-20
locator for BUCHANAN crimping toolHan D
locator for BUCHANAN crimping tool Han C
locator for BUCHANAN crimping tool Han E
depth adjustment gauge tool for BUCHANAN crimping tool
Crimping Tool with Standard ident in plastic case (without locator)
new Rennsteig article No.: 8753 0401 61
E-mail address:
Password:
Warning, important!
This shop addresses commercial costumers only and therefore shows prices excluding tax. If you are an private costumer please activate Cookies and JavaScript in your browser.
You accept this by continuing shopping